Onlangs gezocht

    Electromen OY DC Motor Controller, 11 → 35 V dc, 10 A, 35 V dc

    RS-stocknr.:
    183-7341
    Fabrikantnummer:
    EM-346
    Fabrikant:
    Electromen OY
    Electromen OY
    Bekijk alle Motor Controllers
    tijdelijk niet op voorraad nieuwe voorraad verwacht op 27/06/2023, met een levertijd van 2 à 3 werkdagen.
    Add to Basket
    Aantal stuks

    Toegevoegd

    Prijs Each

    199,35 €

    (excl. BTW)

    241,21 €

    (incl. BTW)

    Aantal stuksPer stuk
    1 +199,35 €
    RS-stocknr.:
    183-7341
    Fabrikantnummer:
    EM-346
    Fabrikant:
    Electromen OY
    Land van herkomst:
    FI

    Datasheets


    Wetgeving en conformiteit

    Land van herkomst:
    FI

    Productomschrijving

    Electromen - EM-346 BLDC MOTOR CONTROLLER, 12-35 V DC, 10 A


    The EM-346 is brushless DC-motor drive for motors with hall sensor feedback.The drive has a MOSFET power stage which provides high efficiency and emits very low RF noise making is suitable for sensitive environments.

    The driver can be used with 120° commutation. This driver has true 4Q power stage, and it makes possible to use regenerative braking.
    In this braking method the supply voltage rises, this voltage rising can be controlled with braking resistor.
    If uses battery supply then the braking energy can be leaded back to battery and braking resistor will not needed.
    The unit accepts digital and analogue (0-5V or 0-10V) command inputs to control speed and direction, analogue providing proportional control if required
    EM-346 has two NPN outputs for fault and overcurrent indication use. Some input and output functions can be modified with parameters.
    Driver includes overvoltage, undervoltage and overtemperature protection and an on board LED can indicate status and fault conditions
    There are open and closed loop modes - open loop (direct control) sets the motor voltage proportional to the control voltage and closed loop mode uses hall sensor feedback for more accurate speed control
    Start and stop ramp settings are available in both these modes as well as parameters to control speed range, closed loop rpm range
    The analogue input is filtered to allow it to accept a PWM signal direct to control speed directly from a PLC
    For parameter setting there is 3 options: EM-236 interface unit, EM-268 with Menthol-Lite PC-program and EM-326 with Menthol-App application for smartphone

    Features and Benefits


    12-48Vdc, 10A continuous, 20-25A peak
    Open & closed loop control operation with hall sensor feedback
    Speed, direction, current limiting, soft start/stop and regenerative braking control
    Compact and DIN rail mountable
    Symmetrical control (rev-stop-fwd) can be achieved with EM-A1 card option

    Three phase output
    Speed and torque control
    Open/closed loop modes
    Regenerative braking with braking resistor output
    Current limit and trip settings
    Symmetrical control (rev-stop-fwd) option
    Fault and overcurrent outputs
    Highly efficient with very low EMC emissions
    DIN rail mountable


    Specificaties

    KenmerkWaarde
    Supply Voltage11 → 35 V dc
    Current Rating10 A
    Voltage Rating35 V dc
    tijdelijk niet op voorraad nieuwe voorraad verwacht op 27/06/2023, met een levertijd van 2 à 3 werkdagen.
    Add to Basket
    Aantal stuks

    Toegevoegd

    Prijs Each

    199,35 €

    (excl. BTW)

    241,21 €

    (incl. BTW)

    Aantal stuksPer stuk
    1 +199,35 €