Onlangs gezocht

    Electromen OY DC Motor Controller, 10 → 35 V dc, 15 A, 12 → 24 V dc

    RS-stocknr.:
    183-7330
    Fabrikantnummer:
    EM-241C
    Fabrikant:
    Electromen OY
    Electromen OY
    Bekijk alle Motor Controllers
    13 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
    37 op voorraad - levertijd is 3 à 5 werkdagen (UK-voorraad)
    Add to Basket
    Aantal stuks

    Toegevoegd

    Prijs Each

    126,44 €

    (excl. BTW)

    152,99 €

    (incl. BTW)

    Aantal stuksPer stuk
    1 +126,44 €
    RS-stocknr.:
    183-7330
    Fabrikantnummer:
    EM-241C
    Fabrikant:
    Electromen OY
    Land van herkomst:
    FI

    Datasheets


    Wetgeving en conformiteit

    Land van herkomst:
    FI

    Productomschrijving

    Electromen - EM-241C DC MOTOR CONTROLLER, 12-24 V DC, 15 A


    The EM-241C is a full bridge brushed DC-motor starter.It is designed to work in a wide range of applications and offers a host of adjustments to optimise control for each application.The drive has adjustable acceleration and deceleration ramps to produce smooth starts and stops.Adjustable current limit protects motor against overcurrent and can also be used to provide an end-stop on current trip.

    This device has also two settable speeds, a useful feature for positioning applications, control inputs are present for basic forward, backward and stop commands, as well as limit switch inputs to define end stops
    This device has also two settable speeds, this can be activated by dedicated input. The same input can be used for analogue speed control signal 0-5V
    Fault output can indicate current trip, over-current or zero-current conditions. It can also be pulled down to ground to disable the drive, if required
    C-version includes wo new parameter: freewheel options for release the rotor of motor, selectable pwm frequency (16kHz pwm being inaudible though current handling capacity is reduced)
    There are two selectable control modes, in continuous mode the motor runs as long as the control is active, in impulse mode it will operate from a momentary command
    Special settings are also available for start-up kick and auto reverse
    For parameters setting there are 3 options: EM-236 interface unit, EM-268 with EmenTool-Lite PC-program and EM-326 with EmenTool-App application for smartphone

    Features and Benefits


    12-24Vdc, 10-15A continuous, 25-30A peak
    Speed, direction, current limiting, soft start/stop and auto-reverse control
    Limit switch inputs for end of travel
    Compact and DIN rail mountable

    Compact with high current output
    Current limit
    Zero current limit
    Overvoltage brake
    Speed setting
    Flexible control inputs
    Impulse / continuous mode
    DIN rail mountable
    Digital parameter - C-version replaces A and B versions
    C-firmware can be loaded B ver. card
    C.version available with Molex connector
    Current limit setting input (new)
    Freewheel options (new)
    2kHz / 16kHz PWM frequency (new)
    * Continuous current output when ambient temp is <50°C
    12-24Vdc version drive =
    15A at 100% speed / 10A at 5-99% speed PWM=2kHz
    10A at 100% speed / 5A at 5-99% speed PWM=16kHz
    Peak ( 5s.) 30A at 2kHz PWM and 25A at 16kHz PWM


    Specificaties

    KenmerkWaarde
    Supply Voltage10 → 35 V dc
    Current Rating15 A
    Voltage Rating12 → 24 V dc
    13 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
    37 op voorraad - levertijd is 3 à 5 werkdagen (UK-voorraad)
    Add to Basket
    Aantal stuks

    Toegevoegd

    Prijs Each

    126,44 €

    (excl. BTW)

    152,99 €

    (incl. BTW)

    Aantal stuksPer stuk
    1 +126,44 €