ADAFRUIT TRINKET 5V MCU Development Board with ATtiny85 - 1501

Datasheets
Wetgeving en conformiteit
Conform
Productomschrijving

Adafruit Trinket Mini Microcontrollers

The Adafruit Trinket development board is now in its second iteration with even more power packed into a board roughly the size of a postage stamp. (measures 27 x 15 x 4 mm) The Trinket development kits feature the Atmel ATtiny85 processor with 8K of flash and 5 I/O pins. There is a USB bootloader so you can plug it into any computer and reprogram just like an Arduino.

This development board is cost effective and provides easy and simple access to the ATtiny85 processor for development and programming.

You cannot stack an Arduino shield on it but for many simple, small, portable or wearable projects, the Trinket could be the perfect platform.

Whats on board?

- Dimensions: 27 x 15 x 4 mm
- ATtiny85 on-board, 8K of flash, 512 bytes of SRAM, 512 bytes of EEPROM
- Internal oscillator runs at 8 MHz, but can be doubled in software for 16 MHz (only with 5 V version)
- USB bootloader with LED indicator
- Micro-USB jack for power and/or USB uploading
- Roughly 5.25K bytes available for use (2.75K taken for the bootloader)
- On-board 3.3 V or 5.0 V power regulator with 150 mA output capability and ultra-low dropout. Up to 16 V input, reverse-polarity protection, thermal and current-limit protection.
- On-board green power LED and red pin #1 LED
- Reset button for entering the bootloader or restarting the program
- 5 GPIO pins - 2 shared with the USB interface. The 3 independent I/O pins have 1 analogue input and 2 PWM output as well. The 2 shared I/O pins have 2 more analogue inputs and one more PWM output.

- Hardware I2C / SPI capability for breakout & sensor interfacing.
- Works with many basic Arduino libraries including Adafruit Neopixel
- 2 mounting holes

The Trinket kits are available in two versions:

- Adafruit Trinket 3.3 V (8 MHz) (RS 124-5509)
- Adafruit Trinket 5 V (8 MHz or 16 MHz) (RS 124-5506)

Both versions work the same, but have different operating logic voltages. We recommend that you use the 3V version with sensors or when powering it with LiPo batteries.

The Adafruit Pro Trinkets are also available in our range:

Adafruit Pro Trinket 3.3V (RS 1245511)

Adafruit Pro Trinket 5V ( RS 1245507)

Note

You can program the Trinket using the Arduino IDE but it is not a fully 100% Arduino compatible.

Adafruit Trinket Microcontrollers (MCU)

Specificaties
Kenmerk Waarde
Classification Development Board
Kit Name TRINKET 5V
Technology MCU
Processor Part Number ATtiny85
Processor Type MCU
12 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
3 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
6,26
(excl. BTW)
7,57
(incl. BTW)
Aantal stuks
Per stuk
1 - 4
6,26 €
5 - 9
6,07 €
10 +
5,95 €
Related Products
A Click accessory module for use with MikroElektronika ...
Description:
A Click accessory module for use with MikroElektronika mikroBUS microcontroller development boards. The GainAMP click board is equipped with a Linear Technology LTC®6912-1 dual channel, low noise, digitally programmable gain amplifier (PGA). The two channels of the PGA can be ...
The USB UART click add-on board is designed ...
Description:
The USB UART click add-on board is designed to add serial UART communication to your design using a USB cable.Features & Benefits of the USB UART click•mikroBUS™ pinout standard•FT232RL USB to UART interface module•USB mini connector•1024 bit EEPROM•128 bytes long ...
The PIC24FJ256GA705 Curiosity Development Board is a 16-bit ...
Description:
The PIC24FJ256GA705 Curiosity Development Board is a 16-bit development platform targeted at first-time users, Makers, and those seeking a feature-rich rapid prototyping board. The PIC24 used here has a full set of low-power features. • 32MHz PIC24FJ256GA705 16-bit XLP microcontroller ...
4G LTE-E click carries the LARA-R211 multi-mode cellular ...
Description:
4G LTE-E click carries the LARA-R211 multi-mode cellular module from u-blox. The board is designed to use 5V power supply. I/O voltage levels could be 3.3V or 5V. It communicates with the target microcontroller over UART interface, with additional functionality ...