Siemens PLC Power Supply 3RX950 Series AS-I Power Supply Unit, 120 V ac, 230 V ac, 30V dc, 5 A 125 x 70 x 125 mm

  • RS-stocknr. 746-6117
  • Fabrikantnummer 3RX9502-0BA00
  • Fabrikant Siemens
Datasheets
Wetgeving en conformiteit
Conform
Land van herkomst: RO
Productomschrijving

AS-i Power Supply - 3RX950 Series

AS-i Power Supplies for 35 mm DIN rail mounting

Integrated ground fault detection
Integrated overload detection
Remote reset and indication
LED status indication
IP20 rated

Approvals

CE, UL

//media.rs-online.com/t_line/L316042-01.gif

Siemens Power Supply Module

The Siemens 30 Vdc power supply module is designed to use with AS-interface PLCs. The supply line voltage ratings are 120ac/230Vac and output current is 5A.
Actuator Sensor Interface, AS-I
AS-I is a method of providing communication from simple discrete components such as an inductive sensor or switching valve via a simple two-wire network to a controlling device such as a PLC or PC.
A unique feature of the AS-I system is the flat, two-core cable (stock no 242-6189) designed to enable fast and easy connection, ensuring correct polarity every time. The cable can be used in a network up to 100m (300m if repeaters are used).
By providing power and data down the same cable, the amount of time normally used to connect sensors and actuators is dramatically reduced, thereby providing savings in cable requirements and man-hours.
The choice of AS-I connection modules enables the user to connect standard sensors/actuators to the BUS with all the address benefits of using dedicated sensors/actuators. It also serves to increase the number of I/O nodes that are available to the user by the use of addressable splitter boxes. The connection modules are available in a variety of packages and can accommodate up to 4 inputs and 4 outputs. This enables up to 124 inputs and 124 outputs to be connected to a single AS-I network.
Another feature of the AS-I system is the method by which the sensors or modules communicate with the host. The design of the communications protocol ensures high data accuracy and error detection capabilities, making the ASI system ideal for automation in noisy and industrial environments.
Benefits of AS-I
Replaces hard wiring
High data speed
Low-cost installation
Intelligent diagnostics
Easy to learn and install
Highly flexible
Can connect to other Fieldbus systems
User-friendly
Off-site pre-assembly and test
Easy maintenance
Faster on-site commissioning
Host or stand-alone use
Able to use standard sensors and actuators (using modules)

Features and Benefits

• Easy to learn and install
• Integrated short circuit protection.
• Intelligent diagnostics
• Integrated overload detection
• Easy maintenance
• Faster onsite commissioning
• Ambient operating temperature ranges between -10°C 70°C

Applications


Industrial automation
• Robotics
• Automobile industry

Certifications


IP20 rated
• UL certified
• CSA certified
• EAC certified

Actuator Sensor Interface (AS-I)

Actuator Sensor Interface, AS-I

AS-I is a method of providing communication from simple discrete components such as an inductive sensor or switching valve via a simple two-wire network to a controlling device such as a PLC or PC.
A unique feature of the AS-I system is the flat, two-core cable (stock no 242-6189) designed to enable fast and easy connection, ensuring correct polarity every time. The cable can be used in a network up to 100m (300m if repeaters are used).
By providing power and data down the same cable, the amount of time normally used to connect sensors and actuators is dramatically reduced, thereby providing savings in cable requirements and man-hours.
The choice of AS-I connection modules enables the user to connect standard sensors/actuators to the BUS with all the address benefits of using dedicated sensors/actuators. It also serves to increase the number of I/O nodes that are available to the user by the use of addressable splitter boxes. The connection modules are available in a variety of packages and can accommodate up to 4 inputs and 4 outputs. This enables up to 124 inputs and 124 outputs to be connected to a single AS-I network.
Another feature of AS-I system is the method by which the sensors or modules communicate with the host. The design of the communications protocol ensures high data accuracy and error detection capabilities, making the ASI system ideal for automation in noisy and industrial environments.

Benefits of AS-I

Replaces hard wiring
High data speed
Low cost installation
Intelligent diagnostics
Easy to learn and install
Highly flexible
Can connect to other fieldbus systems
User-friendly
Off-site pre-assembly and test
Easy maintenance
Faster on-site commissioning
Host or stand alone use
Able to use standard sensors and actuators (using modules)

Specificaties
Kenmerk Waarde
Manufacturer Series 3RX950
For Use With AS-I Power Supply Unit
Line Voltage 120 V ac, 230 V ac
User Power Output Voltage 30V dc
Output Current 5 A
Length 125mm
Width 70mm
Depth 125mm
Dimensions 125 x 70 x 125 mm
8 op voorraad - levertijd is 1 werkdag(en)
Prijs Each
321,00
(excl. BTW)
388,41
(incl. BTW)
Aantal stuks
Per stuk
1 +
321,00 €
Related Products
The CJ1M is a powerful and compact PLC ...
Description:
The CJ1M is a powerful and compact PLC family, covering applications requiring up to 640 I/O. CPU models are available with built in pulse outputs for stepper or servo control, and all CPUs in the CJ1M family enjoy optional modules ...
The M580 PAC is compatible with dual Ethernet ...
Description:
The M580 PAC is compatible with dual Ethernet and X-bus backplanes.One Ethernet switch is embedded in the backplane with connectivity to some slots on the backplane (not all slots have Ethernet connectivity).X-bus functionality is preserved and conforms to the legacy ...
The Omron is a programmable logic controller (PLC) ...
Description:
The Omron is a programmable logic controller (PLC) power supply unit is equipped with many advanced functions like run output function for checking the operation status, as well as the replacement notification function for easy maintenance. The power supply to ...
AS-I is a method of providing communication from ...
Description:
AS-I is a method of providing communication from simple discrete components such as an inductive sensor or switching valve via a simple two-wire network to a controlling device such as a PLC or PC.A unique feature of the AS-I system ...