PR Electronics 3112, Temperature to Current Signal Conditioner, Temperature -200 → +850 °C Input

Datasheets
Wetgeving en conformiteit
Conform
Land van herkomst: DK
Productomschrijving

3000 Series - Temperature Converter

PR Electronics 3000 series temperature transmitters offer reliable and accurate conversion of industry process temperature signals to analogue or digital outputs. The easy DIP-switch set-up allows for more than 1000 different pre-calibrated temperature range combinations. The 3000 series are compact, fast, and easy to use. With a slim 6 mm housing that offers exceptional performance and EMC immunity for dedicated applications.
Designed and rated to operate between -25 ˚C to +70 ˚C, making these devices a good choice in applications where the ambient temperature changes greatly, for example in control panels mounted in outdoor locations. These transmitters have a low temperature coefficient achieving precise measurements, even when the panel is exposed to wide variations in ambient temperature. You can continue to rely on the output signal, with no need to re-calibrate your device.

Features and Benefits

• High basic 0.05% accuracy in all available signal ranges
• All units tested to ensure 2.5 kVAC isolation and have excellent noise immunity
• NAMUR NE21 burst A criteria
• Transmits rapid changes in process measurements to your PLC/DCS for fast and accurate monitoring of critical signals
• Response time of < 30 ms for temperature measurements
• Low temperature coefficient better than 0.01% / °C in a wide -25 to +70°C ambient temperature range for precise measurements
• Long term accuracy better than 0.1% / 3 years with no need for re-calibration

DIP-Switch Programming

Re-calibration is not needed after changing the DIP-switch range settings. Just change the DIP-switch, cycle the power to the unit and obtain the new, pre-calibrated I/O range. HART programming is enabled for selected devices.

Mounting

Devices can be mounted both vertically and horizontally with no air gap separation required. The devices snap onto a power rail or DIN rail and are easily detached by lifting the bottom lock.

High Level of Isolation

Safe galvanic isolation of 2.5 kVAC provides high noise immunity and prevents ground loops for accurate delivery of the process signal to your control system.

Device Status Indicators

A front LED indicates device status, e.g. an error in the set-up, sensor or hardware.

Over Voltage and Polarity Protection

All terminals can withstand up to ±31.2 VDC and are protected against incorrect supply wiring to ensure safe, error-free installation.

PR Electronics DIN Rail Mounting

Specificaties
Kenmerk Waarde
Input Type Temperature
Supply Voltage 16.8 → 31.2 V dc
Minimum Operating Temperature -25°C
Maximum Operating Temperature +70°C
Series 3112
8 op voorraad - levertijd is 1 werkdag(en)
Prijs Each
117,70
(excl. BTW)
142,42
(incl. BTW)
Aantal stuks
Per stuk
1 +
117,70 €
Related Products
PR 3104 flexible signal isolator and converter for ...
Description:
PR 3104 flexible signal isolator and converter for the isolation and conversion of DC signals. Designed for galvanic isolation of current and voltage signals to SCADA systems or PLC equipment.The PR 3000 series is a family of compact, fast, and ...
PR 3105 isolator converter for the isolation and ...
Description:
PR 3105 isolator converter for the isolation and conversion of DC signals. Designed for galvanic isolation of current and voltage signals to SCADA systems or PLC equipment.The PR 3000 series is a family of compact, fast, and easy to use ...
PR 3118 bipolar isolated converter and splitter for ...
Description:
PR 3118 bipolar isolated converter and splitter for conversion of voltage and current bipolar process signals to uni-/bipolar signals. The unit offers 4-port isolation and provides surge suppression and protects control systems from transients and noise.The PR 3000 series is ...
PR 3114 isolated multifunction converter for conversion of ...
Description:
PR 3114 isolated multifunction converter for conversion of linear resistance variation to a standard analogue current / voltage signal, i.e. from solenoids and butterfly valves or linear movements with attached potentiometer. The PR 3000 series is a family of compact, ...