STMicroelectronics X-NUCLEO-PLC01A1 PLC Driver for STM32 Nucleo

Datasheets
Wetgeving en conformiteit
Conform
Productomschrijving

X-NUCLEO-PLC01A1 Industrial PLC Expansion Board

The X-NUCLEO-PLC01A1 is an input/output expansion board which provides an STM32 Nucleo MCU board with industrial PLC (Programmable Logic Controller) functionality.

• 8 x inputs protected by a CLT01-38SQ7 digital termination array • 8 x outputs driving a VNI8200XP octal high-side solid-state relay
• Host communication: SPI bus protected by on-board Si8661 digital isolator
• Status LEDs: Power OK, SPI Activity, Fault, Over-temperature
• 16 x I/O activity LEDs
• Screw connectors for all protected I/O
• Compatible with STM32 Nucleo-64 MCU boards
• Arduino Uno r3 compatible Shield headers
• Designed for situations required to pass IEC61000-4-2 8kV and 15kV test standards
• Free development firmware and example library compatible with STM32Cube firmware

Suitable STM32 Nucleo MCU Boards

802-9412 NUCLEO-F030R8 Cortex-M0 core processor 802-9416 NUCLEO-F103RB Cortex-M3 core processor
802-9425 NUCLEO-F401RE Cortex-M4F core processor

STM32F4 Series 32-Bit ARM Cortex-M4 Microcontrollers, STMicroelectronics

The ARM Cortex-M4 based STM32 F4 series of high-performance MCUs with DSP and FPU instructions is an extension of the industry-leading STM32 portfolio towards even higher performance. Up to 180 MHz operating frequency.

Up to 2x USB 2.0 OTG FS/HS
SDIO (Secure Digital Input Output)
USART, SPI, I²C
I²S (Inter-IC Sound) + Audio PLL
16 and 32 Bit Timers
Up to 3x 12-Bit ADC
Low Voltage 1.7 V to 3.6 V

Specificaties
Kenmerk Waarde
Power Management Function PLC Driver
Kit Classification Expansion Board
For Use With STM32 Nucleo
Tijdelijk niet op voorraad – nieuwe voorraad verwacht op 24/06/2020, met een levertijd van 1 werkdag.
Prijs Each
9,34
(excl. BTW)
11,30
(incl. BTW)
Aantal stuks
Per stuk
1 +
9,34 €
Related Products
The STEVAL-ISA200V1 evaluation board is based on the ...
Description:
The STEVAL-ISA200V1 evaluation board is based on the A6984 high-efficiency monolithic synchronous step-down DC-DC converter chip designed for Automotive applications. • Input voltage: +4.5 to +36Vdc • Output voltage: Adjustable from +0.9V (Board default +3.3V) • Maximum output current: 400mA ...
The NCP1406 is a monolithic micropower PFM step-up ...
Description:
The NCP1406 is a monolithic micropower PFM step-up DC-DC converter. This device is designed to boost single lithium or two cells AA/AAA battery voltage up to 25 V (with internal MOSFET) output for handheld applications. Target applications include OLED Power, ...
The demo board supports the LDO regulator NCP3337 ...
Description:
The demo board supports the LDO regulator NCP3337 in DFN10 package with adjustable output voltage. The ENABLE function allows turn the device to low consumption mode with quiescent current below 1 μA. The Power Good pin allows output voltage monitoring. ...
Description:
A solution to one aspect of Power Over Ethernet (POE) is presented here utilizing the ON Semiconductor NCP1031 series of monolithic, high voltage switching regulators with internal MOSFET. The NCP1031POE evaluation board is an inexpensive, high efficiency, 6.5 W, 5.0 ...