A1120EUA-T Allegro Microsystems,, Unipolar Hall Effect Sensor Switch, 3-Pin SIP

Datasheets
Wetgeving en conformiteit
Conform
Productomschrijving

A1120/1/2/3/5 Chopper Stabilised Hall Effect Sensor Switches, Allegro Microsystems

The Allegro Microsystems A1120, A1121, A1122, A1123, and A1125 Hall-effect, unipolar switches are temperature-stable and stress-resistant sensor ICs. High temperature performance is made possible through dynamic offset cancellation, which reduces the residual offset voltage normally caused by device over-molding, temperature dependencies, and thermal stress.

They include a voltage regulator, Hall-voltage generator, small-signal amplifier, chopper stabilisation, Schmitt trigger, and a short circuit protected open-drain output to sink up to 25 mA. The voltage regulator enables supply voltages of 3 V to 24 V.

For the A1120, A1121, A1122, and A1123, a south pole turns on the output and removal turns off the output. For the A1125, it is reversed and the south pole turns off the A1125 output.

Unipolar switchpoints
Resistant to physical stress
Superior temperature stability
Output short circuit protection
Operation from unregulated supply

Hall Effect Sensors, Allegro MicroSystems

Specificaties
Kenmerk Waarde
Magnetic Type Unipolar
Mounting Type Through Hole
Pin Count 3
Minimum Magnetic Sensor Release Point 5 Gs
Maximum Magnetic Sensor Operating Point 50 Gs
Minimum Operating Supply Voltage 3 V
Maximum Operating Supply Voltage 24 V
Length 4.09mm
Width 1.52mm
Height 3.02mm
Dimensions 4.09 x 1.52 x 3.02mm
Minimum Operating Temperature -40 °C
Maximum Operating Temperature +85 °C
Package Type SIP
Typical Magnetic Sensor Hysteresis 10 Gs
1660 op voorraad - levertijd is 1 werkdag(en).
Prijs Each (In a Pack of 5)
0,804
(excl. BTW)
0,973
(incl. BTW)
Aantal stuks
Per stuk
Per pak*
5 - 20
0,804 €
4,02 €
25 - 95
0,668 €
3,34 €
100 - 245
0,552 €
2,76 €
250 - 495
0,516 €
2,58 €
500 +
0,486 €
2,43 €
*prijsindicatie
Verpakkingsopties
Related Products
The ATS468 is a true zero-speed gear tooth ...
Description:
The ATS468 is a true zero-speed gear tooth sensor IC consisting of an optimized Hall IC and a permanent magnet pellet configuration in a single overmolded package. The integrated circuit provides a manufacturer-friendly solution for digital gear tooth sensing applications. ...
The A1225/7/9 High Temperature Hall Effect Latches are ...
Description:
The A1225/7/9 High Temperature Hall Effect Latches are temperature-stable and stress resistant suitable for operation for temperatures up to 150°C. A Schmitt trigger circuit maintains operate and release point symmetry by compensating for temperature changes in the Hall element. Internal ...
The A3211/2 are ultrasensitive, pole independent, Hall-effect switches ...
Description:
The A3211/2 are ultrasensitive, pole independent, Hall-effect switches with latched digital output. Their 2.5 V to 3.5 V operation and unique clocking scheme reduces the average operating power to less than 15 μW with a 2.75 V supply.Either a north ...
The Allegro A1101/2/3/4 and A1106 Hall-effect switches are ...
Description:
The Allegro A1101/2/3/4 and A1106 Hall-effect switches are produced with BiCMOS technology enabling fast power-on time and low-noise operation. Device programming is performed after packaging, to ensure increased switch-point accuracy by eliminating offsets that could be induced by package stress.Unique ...