XY2-CE Cable Switch, Left Side, 50m, NO/NC

Datasheets
Wetgeving en conformiteit
Conform
Productomschrijving

Telemecanique XY2CE & XY2CB Emergency Stop Rope Pull Switches

These emergency stop trip wire switches are designed to reduce the risk of injury to persons and damage either to machines or work in progress. They can be tripped by a single human action when a normal emergency stop function is not available and will also trip in the event of the trip wire breaking.

Switches incorporate positive opening operation contacts, the tripping of the switch being made with positive action
The switch latches in the tripped position (N/C safety contact(s) open). The function of the N/O contact is purely for signalling
Incorporates a reset button, which re-closes the safety contact(s), restarting of the machine must only be achieved by manual operation of a control device within the machine start circuit, remote to the trip wire switch
Recommended distance between cable supports is 15m (for model XY2-CB30 a distance of 20m is recommended)
The XY2 CE1A296 comes with a pilot light (direct supply)

Note

The XY2 CB switch must not be used if the installation requires that the trip wire be angled but the XY2 CE switch can. In this case, the total sum of the angles through which the trip wire bends must not exceed 180°.

Standards

EN/ISO 13850:2006

Telemecanique Sensors Emergency Stop Rope Pull Switch

The Telemecanique Sensors XY2CJ series emergency stop rope pull switch has a 1NO/1NC contact configuration. It has Zamak housing and maximum AC/DC voltage is 240VAC and 250VDC and the current rating of the switch is 3A and 270mA for AC and DC respectively. It is designed to prevent injury to people or damage to machinery when a normal emergency stop function is not available. This product is easy to install and offers a quick visual check of the switch status for machine restart. This switch has a rope span of 50m and the mounting orientation is to the left side. Note: Manufacturer part numbers with the suffix H29 are the ISO M20 threaded cable entry version.

Features and Benefits

• Switches incorporate positive opening operation contacts with the tripping of the switch being made with positive action • Switch latches in the tripped position (N/C safety contact(s) open) • Function of the N/O contact is purely for signalling • Incorporates a reset button, which re-closes the safety contact(s), restarting of the machine must only be achieved by manual operation of a control device within the machine start circuit, remote to the trip wire switch • Recommended distance between cable supports is 50m • Comes with a pilot light (direct supply) • Size of cable entry is PG13.5

Certifications

• EN/ISO 13850:2006 • IP65 rated

Specificaties
Kenmerk Waarde
Range Preventa
Series XY2-CE
Reset Button Yes
Normal State Configuration NO/NC
Mounting Orientation Left Side
Maximum Rope Span 50m
Maximum Current 3 A ac, 270 mA dc
Maximum AC Voltage 240V
Maximum DC Voltage 250V
Number of Cable Entries 1
Conduit Entry PG13.5
Size of Cable Entries PG13.5
Maximum Operating Temperature +70°C
E-Stop Button No
Minimum Operating Temperature -25°C
Length 142mm
Depth 105mm
Dimensions 142 x 229 x 105 mm
Width 229mm
IP Rating IP65
1 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
1 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
268,00
(excl. BTW)
324,28
(incl. BTW)
Aantal stuks
Per stuk
1 +
268,00 €
Related Products
The Telemecanique sensors XY2CE is 240VAC voltage wire ...
Description:
The Telemecanique sensors XY2CE is 240VAC voltage wire switch. It has E-stop rope pull switch on right side-2NC+2NO with yellow pilot light, 230V-boot. • Contact operation slow break• Cover material is stainless steel• Housing material is Zamak• Maximum rope span ...
The Lifeline 4 rope pull switch, also known ...
Description:
The Lifeline 4 rope pull switch, also known as a cable pull switch or grab wire switch, can be installed along or around awkward machinery such as conveyors and provides constant emergency stop access. The positive mode mechanism helps ensure ...
The Lifeline 4 rope pull switch can be ...
Description:
The Lifeline 4 rope pull switch can be installed along or around awkward machinery such as conveyors and provide a constant emergency stop access. It is made from stainless steel 316 and is suitable for applications where there are hygiene ...
The PSENrope from Pilz is a manually operated ...
Description:
The PSENrope from Pilz is a manually operated rope pull switch used to safely shut down functional processes that extend over a wide area, such as conveyors. It provides maximum safety, as the emergency stop function can be triggered at ...