ATMEL-ICE PCBA KIT,ATATMEL-ICE-PCBA

  • RS-stocknr. 130-6124
  • Fabrikantnummer ATATMEL-ICE-PCBA
  • Fabrikant Microchip
Datasheets
Wetgeving en conformiteit
Conform
Productomschrijving

ATATMEL-ICE PCBA

The Atmel-ICE series consists of development tools for debugging and programming ARM Cortex-M based Atmel SAM and Atmel AVR microcontrollers with on-chip debug capability. The Atmel-ICE series supports JTAG, SWD, PDI, TPI, aWire, SPI and debugWIRE interfaces and is compatible with Atmel Studio.

Kit Contains:

Atmel-ICE unit without plastic encapsulation130-6122 Full Kit available130-6123 Basic Kit available

System Requirements

The Atmel-ICE unit requires that a front-end debugging environment Atmel Studio version 6.2 or later is installed on your computer. The Atmel-ICE should be connected to the host computer using the USB cable provided, or a certified Micro-USB cable.

How to turn the Atmel - ICE on?The Atmel-ICE is powered by the USB bus voltage. It requires less than 100mA to operate, and can, therefore, be powered through a USB hub. The power LED will illuminate when the unit is plugged in. When not connected in an active programming or debugging session, the unit will enter low-power consumption mode to preserve your computer's battery. The Atmel-ICE cannot be powered down - it should be unplugged when not in use. How does it connect?The Atmel-ICE communicates primarily using a standard HID interface and does not require a special driver on the host computer. The Atmel-ICE must be connected to an available USB port on the host computer using the USB cable provided, or suitable USB certified micro cable. The Atmel-ICE contains a USB 2.0 compliant controller and can operate in both full-speed and high-speed modes. For best results, connect the Atmel-ICE directly to a USB 2.0 compliant high-speed hub on the host computer using the cable provided.

Kit Types:

Cable kit: 177-9591Adapter kit: 177-9590Basic kit: 130-6123PCBA kit: 130-6124Full kit: 130-6122

9 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
9 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
48,99
(excl. BTW)
59,28
(incl. BTW)
Aantal stuks
Per stuk
1 +
48,99 €
Related Products
The PICkit™ Serial Analyzer is a USB-based tool ...
Description:
The PICkit™ Serial Analyzer is a USB-based tool used to direct communication between a PC and an external serial device Simplifies the chore of managing serial communication with a device under test. The Windows® GUI configures the hardware and ’scripts’ ...
Flasher Portable PLUS has been designed to fill ...
Description:
Flasher Portable PLUS has been designed to fill the need for a portable, battery-operated production-grade Flash memory programmer used for in-field firmware updates. Initial setup/preparation for stand-alone mode operation is done via the J-Flash software. It supports storage of multiple ...
The FlashBios is a device Reader/Programmer/Copier supporting CMOS ...
Description:
The FlashBios is a device Reader/Programmer/Copier supporting CMOS EPROMs (2716 to 27C801 family) of 16Kb to 8Mb, parallel EEPROMs (28C16 to 28C040 family) up to 4Mb, parallel FLASH memory (28xxx, 29xxx, 37xxx, 39xxx, 49xxx, etc) of 512Kb to 8Mb, I²C ...
The FlashBiosBox is a device Reader/Programmer/Copier supporting EPROMs ...
Description:
The FlashBiosBox is a device Reader/Programmer/Copier supporting EPROMs (2716 to 27C801 family) of 16Kb to 8Mb, parallel EEPROMs (28C16 to 28C040 family) up to 4Mb, parallel FLASH memory (28xxx, 29xxx, 37xxx, 39xxx, 49xxx, etc) of 512Kb to 8Mb, I²C and ...