Ultimaker Nozzle for use with Olsson Block 0.4mm

  • RS-stocknr. 110-1983
  • Fabrikantnummer OBN002
  • Fabrikant Ultimaker
Datasheets
Wetgeving en conformiteit
N.v.t.
Land van herkomst: NL
Productomschrijving

Ultimaker 2 Jet Nozzles

The Olsson block brass Jet nozzles have a special tip angle and shoulder width, they also have a special internal geometry with an angle less steep down to the nozzle hole. A special treatment applied inside also makes them slip more. You can print 3°C to 5°C lower because of this treatment, and is also useful for oozing and drips.

With these special nozzles, you can print faster, the plastic flows much more easier than in classic nozzles. You can also clean them efficiently with cold pulls (or atomic pulls). The geometry of the inside makes it easier to get rid of plastic so changing colours or filament type is done faster and safer.

Use the 0.25mm brass nozzle to print small detailed prints, it's an expert nozzle (RS 110-1982)
The 0.4mm (RS 110-1983) is the standard size for a lot of 3D printers
If you print in wood filaments, this brass nozzle of 0.8mm is perfect for the job (RS 110-1985)

Note

This nozzle is compatible with M6 Threads, you can put it on the Ultimaker Original (the fan shroud must be modified) or any of the Ultimaker family that has the Olsson Block mounted.

Ultimaker 3D Olsson Block Brass Jet Nozzle Printing Parts & Accessoriess

The Ultimaker allows for quick and easy nozzle changes, so different nozzle sizes can be selected to suit each project. Use a smaller nozzle to print fine lines for more detail, or use a larger nozzle to print thicker lines to decrease print duration. The Olsson block brass Jet nozzles have a special tip angle and shoulder width, they also have a special internal geometry with an angle less steep down to the nozzle hole. A special treatment applied inside also makes them slip more. Note: This nozzle is compatible with M6 Threads, you can put it on the Ultimaker Original (the fan shroud must be modified) or any of the Ultimaker family that has the Olsson Block mounted.

Features and Benefits

Clean them efficiently with cold pulls Print faster, the plastic flows much easier than in classic nozzles The 0.4mm is the standard size for a lot of 3D printers The geometry of the inside makes it easier to get rid of plastic so changing colours or filament type is done faster and safer Use the 0.25mm brass nozzle to print small detailed prints

Ultimaker Accessories

Specificaties
Kenmerk Waarde
Product Type Nozzle
Nozzle Material Brass
For Use With Olsson Block
Nozzle Size 0.4mm
9 op voorraad - levertijd is 1 werkdag(en) (EU-voorraad)
59 op voorraad - levertijd is 1 werkdag(en) (UK-voorraad)
Prijs Each
34,75
(excl. BTW)
42,05
(incl. BTW)
Aantal stuks
Per stuk
1 +
34,75 €
Related Products
The Robox replacement Dual Material head consists of ...
Description:
The Robox replacement Dual Material head consists of 2 independently controlled heated nozzles each with the unique Robox needle valve control system. Allows you to print with 2 materials or 2 colours in the same material on the same layer. ...
The V2 perforated plate is another component that ...
Description:
The V2 perforated plate is another component that is useful while printing models with precise dimensions. It is mounted on the heated bed and the plate helps prevent distortions in the print. This new version is thicker and more stable ...
The RS Pro extruder fits a wide range ...
Description:
The RS Pro extruder fits a wide range of 3D printers, could use in Mendel, Prusa, RepRap, MakerBot or any other DIY 3D Printer. Extruder for 3D Printer Matches most 3D Printers.
The 1.75 mm plastic extruder from Zmorph is ...
Description:
The 1.75 mm plastic extruder from Zmorph is a basic solution for single material 3D printing. The extruder is made from aluminium and stainless steel, while brass filament drives (toothed pulley) ensure the filament is gripped securely and doesnt slip. ...