Crimp Tool Positioners, Turrets & Locators

Crimp Tool Positioners are parts of a Crimping tool designed to adapt the tool frame to a particular application. Available in a wide selection of sizes and shapes locators guarantee versatility of every crimping tool. The data plate on each positioner designates which contacts the positioner accommodates for its wire size and indicates selector position. The positioners are easy to remove and replace when different connector size is required.


How easy crimping tools and positioners, turrets and locators are to use?


They are very easy to use, insert the contact pin into the hole of the crimp tool, load the wire into the contact pin, make sure it’s fully seated then and squeeze until the cycle finishes then finally check that you have a secure crimp.


How do you maintain the product?


There is very little maintenance required for this tool, keep the indenter tips free of debris and dirt.


The Importance of a High-Quality Crimp


When a crimping tool is used on a terminal, two crimps take place at the same time. One is the electrical connection between the conductor and the terminal. The other is the insulation crimp which provides strain relief against vibration and tension.The electrical connection must be gas-tight without any voids between the wire strands and the terminal. If there are any voids present, then corrosion can occur causing resistance and excessive heat which damages the electrical connection. Using a good quality crimping tool will ensure that a full, gas-tight crimp is produced preventing future deterioration of the electrical connection and insulation breakage.


...
Lees meer Lees minder

Filters

1 - 20 van 169 producten worden weergegeven
Resultaten per pagina
Omschrijving Prijs Type Series Number of Contacts Series Number
RS-stocknr. 531-425
FabrikantRS PRO
63,18 €
Each
Aantal stuks
Positioner QM/TNM 16 -
RS-stocknr. 191-6811
FabrikantRS PRO
33,90 €
Each
Aantal stuks
Positioner - - -
RS-stocknr. 314-8414
Fabrikantnummer86-5
86,63 €
Each
Aantal stuks
Positioner M22520/7-06 - -
RS-stocknr. 515-1096
FabrikantnummerM22520/2-09
FabrikantGlenair
236,79 €
Each
Aantal stuks
Positioner M22520/2-09 - -
RS-stocknr. 787-9566
FabrikantnummerS16RCM16
FabrikantSouriau
314,63 €
Each
Aantal stuks
- UTS Series 16 -
RS-stocknr. 760-0180
FabrikantnummerDCE.91.070.3MVM
FabrikantLemo
96,38 €
Each
Aantal stuks
Positioner M - -
RS-stocknr. 696-1642
FabrikantnummerTA-0002-146-0001
FabrikantAmphenol
31,75 €
Each
Aantal stuks
Locator TA - -
RS-stocknr. 876-2056
Fabrikantnummer169403
FabrikantTE Connectivity
27,96 €
Each
Aantal stuks
Locator AMP - -
RS-stocknr. 360-1713
FabrikantnummerTH1A
FabrikantGlenair
228,96 €
Each
Aantal stuks
Turret M22520/1-02 - -
RS-stocknr. 314-7590
FabrikantnummerTH163
171,66 €
Each
Aantal stuks
Turret M22520/1-04 - -
RS-stocknr. 822-7755
Fabrikantnummer63819-0975
FabrikantMolex
54,45 €
Each
Aantal stuks
Locator T9999 - 63819
RS-stocknr. 822-7717
Fabrikantnummer63811-8775
FabrikantMolex
45,72 €
Each
Aantal stuks
Locator T9999 - 63811
RS-stocknr. 864-7017
Fabrikantnummer69082
FabrikantTE Connectivity
8.822,53 €
Each
Aantal stuks
Crimping Head DYNA-CRIMP - -
RS-stocknr. 713-3671
FabrikantnummerVH435
FabrikantGlenair
182,62 €
Each
Aantal stuks
Turret ITS - -
RS-stocknr. 756-7345
Fabrikantnummer09990000531
FabrikantHARTING
170,39 €
Each
Aantal stuks
Positioner D-sub - -
RS-stocknr. 765-9858
Fabrikantnummer15019/SP
FabrikantBulgin
126,85 €
Each
Aantal stuks
Positioner 6000 - -
RS-stocknr. 876-2080
Fabrikantnummer4-539785-7
FabrikantTE Connectivity
55,17 €
Each
Aantal stuks
Locator Mini CERTI-LOK - -
RS-stocknr. 864-6991
Fabrikantnummer1583659-1
FabrikantTE Connectivity
1.212,15 €
Each
Aantal stuks
Hydraulic Foot Pump - - -
RS-stocknr. 329-9843
Fabrikantnummer09990000304
FabrikantHARTING
50,59 €
Each
Aantal stuks
Crimping Head - - -
RS-stocknr. 114-7920
Fabrikantnummer09990000112
FabrikantHARTING
11,97 €
Each
Aantal stuks
Locator Han-Com - -
Related Products
The multi-contact is an MES-CZ series, locator adjustable ...
Description:
The multi-contact is an MES-CZ series, locator adjustable crimp tool. It is suitable for crimping from 0.14 to 4mm² cables with 1mm, 1.5mm, and 3mm with CombiTac contacts. The wire size of tool ranges between 26AWG and 22 AWG. It ...
Lightweight design and very high density, microComp® is ...
Description:
Lightweight design and very high density, microComp® is an alternative to HD DSUB with superior characteristics,A flexible alternative to MIL-STD 83513 connectors. Stainless steelCompatible with MIL-STD 83513 interfaces.
Bulgin Buccaneer 6000 series tooling and accessories suitable ...
Description:
Bulgin Buccaneer 6000 series tooling and accessories suitable for use with the 6000 series of metal and plastic circular connectors, including a gland pack covering 4-10mm diameter cables, various contact removal tools for differing connector contacts, screening clamp and crimp ...
CF 3000 series 120V portable electrical bench press ...
Description:
CF 3000 series 120V portable electrical bench press for the automatic stripping and crimping of DIN 46228-4 taped insulated crimp wire ferrules with a wire size range of 0.25 to 2.5mm2 (24-14 AWG). This CF 3000 crimping and stripping bench ...